- Provides accurate Lambda measurement, even when exhaust gas temperature is changing rapidly (heating or cooling).
- Calibrated by the user for a particular sensor using either the initial sensor factory calibration or the free air calibration.
- Pre-configured to suit a single unit installation. If necessary, the configuration can be adjusted; see the Configuration section for more details.
- Units marked with a 2 or higher under the barcode are able to transmit extended Lambda values (Rich Lambda).
OVERVIEW
MoTeC’s LTC (Lambda To CAN) monitors, controls and diagnoses a Bosch LSU 4.9 Lambda sensor, transmitting Lambda readings on a CAN bus. When using multiple LTCs, up to 32 Lambda sensors can be configured on a single CAN bus for simultaneous monitoring by an ECU or logging device.
FEATURES
COMPATIBILITY
MoTeC ECU: M1 Series, M84, M400, M600, M800, M880
MoTeC Display/Loggers: All C Series Display Loggers, ACL, CDL3 (and discontinued models: SDL, SDL3, ADL, ADL2, ADL3)
PC COMMUNICATION
A MoTeC gateway device is required to communicate with the LTC on CAN. Such devices include:
- M1 Series ECUs
- All C Series Display Loggers, ACL, ADL3, SDL3, CDL3
- UTC (USB to CAN) #61059
SPECIFICATIONS
Inputs/Outputs
- 1 x Bosch LSU 4.9 Lambda sensor
- Power supply voltage 11 V – 16 V
- Power supply current 110 mA typical plus the sensor heater current. Heater current is typically 0.5 A – 1 A and up to 2 A on startup.
Communications
- 1 x CAN – using LTC Manager, configurable to:125 Kbps, 250 Kbps, 500 Kbps or 1 Mbps
Physical
- Dimensions: 38 x 26 x 14 mm, excluding wiring looms and connectors
- Weight: 62 g
- 1 x 4 pin male DTM connector (power/CAN)
- 1 x mating connector for Bosch LSU 4.9 sensor
- Maximum ambient temperature: 100 °C
SOFTWARE
For multiple installations, LTC Manager software allows all units to be simultaneously managed and diagnosed.
The software is used to:
- Configure and calibrate all units on the CAN bus
- Display readings and diagnostics
- Configure CAN transmission addresses
- Control free air sensor calibration
- Update unit firmware
CONFIGURATION
MoTeC LTCs come pre-configured to suit a single LTC unit installation. By default, the initial factory sensor calibration is used and the CAN address is 460.
It is only necessary to use LTC Manager if installing multiple LTC units, or if changes to the default settings are required.
DEMINSIONS AND MOUNTING
All dimensions in mm.
CONNECTOR PINOUTS
Connector A (and B for Dual version)
Bosch LSU 4.9 sensor connector
Mating connector: supplied on sensor
| Pin | Wire Colour | Description |
|---|---|---|
| 1 | Red | Ip |
| 2 | Yellow | Sensor 0 V |
| 3 | White | Heater – |
| 4 | Grey | Heater + |
| 5 | Green | Ipr |
| 6 | Black | Vs |
Power/CAN Connector
DTM 4 Pin (M) (#68055)
Mating connector: DTM 4 Pin (F) #68054
| Pin | Wire Colour | Description |
|---|---|---|
| 1 | Black | Battery – |
| 2 | Green | CAN Lo |
| 3 | White | CAN Hi |
| 4 | Red | Battery + |
WIRING
To power the LTC, connect to either the ignition switch for fast sensor startup or the fuel pump relay to prevent accidental battery drainage.
Wiring example
For information on wiring a CAN bus with several LTCs and any number of other CAN devices (as per the example), refer to the relevant device manual.
Brand
MoTec
Be the first to review “MoTeC – LTC BOSCH 4.9”
Related products
-
Sale!
Mustang EcoBoost
Corsa – 2021-2022 Ford Bronco 2.7L 4-Door 5in Cat-Back Single Side Exhaust w/ Turndown Exhaust Tip
-
-
Reviews
There are no reviews yet.